TBP-TEVA萃取色层分离-α能谱法测定辐照镎靶溶解液中痕量236Pu的可行性

²³⁶Pu的含量控制是钚热源的一项重要参数，通过α能谱准确测量镎靶溶解液中痕量²³⁶Pu，建立镎靶辐照靶件溶解液中钚的分离方法。根据杂质组成特点采用TBP-TEVA萃取色层双柱分离，用氨基磺酸亚铁以及亚硝酸钠对钚进行调价，对靶件溶解液中的Al、Fe、U、Th和Np等进行分离，去污系数均大于10⁴，钚的回收率为90.7%。研究大量²³⁸Pu对α能谱测定²³⁶Pu的干扰，结果表明，大量²³⁸Pu会造成仪器本底升高，²³⁸Pu能谱峰分辨率降低；在7 500 Bq ²³⁸Pu干扰下，测量4.3 h 时，²³⁶Pu的最小可检测活度为1.20×10^-2 Bq（当量质量为6.11×10^-16 g）。计算结果表明，镎靶溶解液样品中钚的同位素比值n(²³⁶Pu)/n(²³⁸Pu) ≥4.63×10^-8时，取合适的样品量使得电沉积源中²³⁸Pu 活度在 450~7 500 Bq范围内，均可测量其中的痕量²³⁶Pu，同时可准确测定同位素比值n(²³⁶Pu)/n(²³⁸Pu)。     

基于经验模态分解方法的拉曼光谱信号处理研究

经验模态分解(EMD)方法是一个以信号内在物理频率成分为对象的自适应时频分析方法,而常见的非平稳信号分析方法,比如小波分析,它需要选择小波基,不同小波基的分析结果不同;拉曼光谱信号是典型的非线性和非平稳信号,EMD方法充分地保留了信号本身的非线性和非平稳的特征,适应于拉曼光谱信号的分析。实验在自行研制的拉曼光谱测试平台上获得了原始的拉曼光谱信号,并通过经验模态分解将信号分解成不同频率的10个本征模式分量,信号能量集中在750cm^-1和1500cm^-1左右,最后进行了频率成分分析和去噪处理,并和小波分析方法进行了对比,验证了EMD方法的有效性和实用性,该方法在拉曼光谱信号分析中有较好的应用前景。     

简捷水热法制备氟化石墨烯及其表征

氟化石墨烯是一种石墨烯衍生物,在润滑材料、电子器件等领域具有广阔的应用前景。采用回流搅拌并水热还原的方法制备氟化石墨烯,并在不加HF的情况下以同样的方式制备了水热还原的还原氧化石墨烯(rGO)。采用傅里叶变换红外光谱(FTIR)、X射线衍射(XRD)、拉曼光谱(Raman)、X射线光电子能谱(XPS)、透射电镜(TEM)等对样品进行形貌观测和表征。FTIR的结果表明氟化产物中含有C-F键和部分未完全还原的含氧基团;由XRD谱可以看出,产物晶型较差,其层间距和原料的性质有关;Raman谱证实了石墨烯的基本结构依然存在,但也存在大量缺陷,并且rGO比FGS的规整度略高;XPS谱表明样品表面有氟元素的存在,意味着FGS制备成功;TEM结果显示该样品为单层和少层。该方法操作简单、原料廉价易得、工艺要求不高,适用于批量生产氟化石墨烯。     

Immobilization of simulated waste into pure Gd2Zr2O7 pyrochlore without space occupancy design

In this study, different molar ratios of Nd:Ce were directly mixed with prepared pure Gd₂Zr₂O₇ powders without space occupancy design. Samples were obtained by performing sparking plasma sintering (SPS) at 1750°C for 5 minutes. X-ray diffraction (XRD) results show that maximum solid solubility of simulated radionuclides can reach 50 mol%. In addition, all samples with the maximum solid solubility have high compactness, and all elements are evenly distributed on the surface of the samples. The samples show a better crystallization effect as the molar ratio of Nd:Ce increases. The maximum solid solubility increases from 42 mol% to 50 mol% when the amount of Nd₂O₃ reaches 66 mol%.     

Effect of Yb concentration on the microstructures,spectra, and laser performance of Yb: CaF2 transparent ceramics

Ytterbium-doped calcium fluoride transparent ceramics is considered as a promising laser gain medium. How to prepare low scattering loss ceramics is the main challenge at present. In this study, a simple route of hot-pressing method was introduced to fabricate high optical quality of Yb: CaF₂ laser ceramics with different concentration of Yb ions. The influence of Yb concentration on the particle sizes of the powders, microstructure, fluorescence spectra, output power, and laser emitting spectra of Yb: CaF₂ transparent ceramics was discussed. About 976 nm LD pumped CW laser operation has been demonstrated in 1, 2, 4, and 5 at.% Yb doped CaF₂ ceramics. A maximum average output power of 0.809 W was obtained for the 5 at.% Yb: CaF₂ ceramics with the slope efficiency was 26%.     

Relative vibration identification of cutter and workpiece based on improved bidimensional empirical mode decomposition

Frontiers of Mechanical Engineering - In the process of cutting, the relative vibration between the cutter and the workpiece has an important effect on the surface topography. In this study, the...     

高紫外反射ZnO/SiO2复合粉体制备及其热控涂层性能研究

目的 以ZnO/SiO2复合粉体为填料，开展新型热控涂层制备方法研究，提高传统白色热控涂层的紫外反射率, 研制出具有太阳全光谱高反射性能的热控涂层。方法 以硫酸锌和硅酸钠为原料，采用常温化学合成与高温热处理相结合的方法制备ZnO/SiO2复合粉体，通过X射线衍射仪、扫描电子显微镜及紫外可见分光光度计等仪器，对复合粉体的微观结构及光学性能进行表征。然后以ZnO/SiO2复合粉体为填料，以无机硅酸钾为粘结剂，制备了ZnO/SiO2热控涂料，通过不同颜基比和厚度的优化，得到了太阳全光谱(200~ 2600 nm)高反射白色热控涂层的制备方法。结果 研制的ZnO/SiO2复合粉体在紫外波段的反射率均大于88%，与传统ZnO粉体相比具有明显提升。当以无机硅酸钾为粘结剂、颜基比为2:1、喷涂厚度为100~140 μm时，所制备涂层在太阳全光谱呈现高反射特性，此时涂层的太阳吸收比为0.12，红外发射率为0.92。结论 ZnO/SiO2热控涂层具有优异的热控性能，与传统白色热控涂层相比具有更低的吸收比，同时在太阳全光谱具有高反射特性，可以满足新一代大功率卫星长寿命和高效散热的技术需求。